PVI Industries 1000PHE125A-TPGO Manuel d'utilisateur télécharger pdf

 Recoveries based on 83% thermal efficiency. ASHRAE 90.1 compliant for efficiency and standby loss.

 “J” dimension is for the burner housing only. Gas train may exceed this dimension.

 Standard gas train.

* The information presented is for Natural gas 0.6 S.G.— For operation with propane (LP gas), consult factory.

Dimensions are in inches unless otherwise specified.

Burner control panel requires 18" clearance for door swing.

For standard and optional equipment, see form PV 6047.

Model

Number

Recovery gph 

Input

Btu/h

Min. Inlet Flow

Gas Pressure

"W.C. 

#2 Oil

gph

Dimensions (inches)

Blower

Motor

Shipping

Weight

lbs

40°- 120°F 40°- 140°F A B C J  HP

Volt/Ph/

Amps

750 PHE 125A-TPGO 750 600 600,000 4.5 4.3 42 6 1 31 1/2

115/1∅/10

1420

1000 PHE 125A-TPGO 1000 800 800,000 6.0 5.7 42 8 1 31 1/2

115/1∅/10

1460

1250 PHE 125A-TPGO 1250 1000 1,000,000 7.5 7.2 42 8 1 31 3/4

115/1∅/14

1550

1500 PHE 125A-TPGO 1500 1200 1,200,000 7.5 8.6 42 8 1-1/4 31 1

115/1∅/16

1630

TURBOPOWER

GAS/OIL  PACKAGED WATER HEATER

POLYSHIELD

POLYMER-LINED STORAGE TANK

TANK SERIES 125 GALLONS

HORIZONTAL

PV 5477 02/04

PVI INDUSTRIES, LLC

FORT WORTH, TEXAS 76111

(800) 784-8326

 (817) 335-9531  www.pvi.com

Product is patented in the U.S., Canada, and Mexico.

STANDARD ELECTRICAL REQUIREMENTS

CONTROL VOLTAGE: 120V, 1Ø, 60 HZ., 2 AMPS.

MOTOR VOLTAGE:

208V, 230V, AND 460V MOTORS ARE AVAILABLE BUT WILL

REQUIRE A SEPARATE 120V/2 amps CONTROL CIRCUIT OR AN

OPTIONAL CONTROL CIRCUIT TRANSFORMER.

* REAR ACCESS MODULE

MODEL PREFIX M L STD or OPTIONAL

750-1500 23" N/A OPTIONAL

PVI RESERVES THE RIGHT TO CHANGE THE DESIGN

AND SPECIFICATION WITHOUT NOTICE.

* GAS PRESSURE REQUIREMENTS

SEE TABLE FOR MINIMUM PRESSURE BY MODEL NUMBER.

MAXIMUM STATIC INLET PRESSURE: 14" W.C.

FOR PRESSURES OTHER THAN LISTED, CONSULT FACTORY.

Pressure shown is for standard UL gas train. Additional controls

may increase pressure requirements.

VENTING REQUIREMENTS

-.02" TO -.06" W.C. (NEGATIVE PRESSURE)

ENTIRE VENT SYSTEM SHOULD NEVER BE SIZED BASED

UPON THE VENT CONNECTION DIAMETER EXCLUSIVELY.

FOR PROPER SIZING, CONSULT

THE NATIONAL FUEL GAS CODE UNDER “FAN-ASSISTED.”

TURBOPOWER 1

Résumé du contenu

Page 1 - TURBOPOWER

 Recoveries based on 83% thermal efficiency. ASHRAE 90.1 compliant for efficiency and standby loss.  “J” dimension is for the burner housing on

Commentaires sur ces manuels

Pas de commentaire

PVI Industries 1000PHE125A-TPGO Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Non PVI Industries 1000PHE125A-TPGO. PVI Industries 1000PHE125A-TPGO User's Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Non PVI Industries 1000PHE125A-TPGO